A single line diagram (SLD, also called a one-line diagram) is the drawing that explains an electrical installation on one page. It shows the power path from the source to the loads using one line for each circuit, even when the real circuit has three phases and a neutral. If you buy or build a main distribution board (MDB) or sub-main distribution board (SMDB), the SLD is the document the panel is built from.
What a single line diagram shows
- The source: the utility supply or transformer and, where present, a generator. If there is a generator, an automatic transfer switch shows how the load moves between sources; see the ATS panel guide.
- The MDB: the incoming breaker, the busbar and the outgoing breakers.
- The SMDBs and distribution boards (DBs): each one fed by a cable from an MDB outgoing, with its own incomer and outgoing circuits. The difference between the board types is explained in MDB, SMDB and DB panel types.
- Protection and control devices: breakers, residual current devices, fuses, isolators, contactors and metering.
- Cables and busbars: size, number of cores, length and the breaker that protects each one.
- Loads: each outgoing circuit with its description and its load in kW or amperes.
How to read it, step by step
- Start at the source and follow the line downward. Everything above a device is its supply; everything below is what it protects.
- Read the incomer of each board. Note its rated current, the number of poles and its breaking capacity, which must be at least the prospective short-circuit current at that point. A breaking capacity is the highest fault current the device can interrupt safely; see MCB vs MCCB for how it differs between breaker types.
- Follow each outgoing circuit to its cable label. A cable label normally gives the number of cores, the conductor size, the insulation type and the length.
- Check the ratings step down. A breaker feeding a sub-board is normally larger than the breakers inside that sub-board. If it is not, the designer should be asked why.
- Look for the busbar rating on each board and the short-circuit withstand rating it must carry. The busbar itself is covered in the busbar guide.
- Read the notes. Notes give the system voltage, frequency, earthing system, enclosure rating, form of separation and the standards the design follows.
Symbols
SLDs use standard graphical symbols. Different offices use slightly different drawings for the same device, so a legend on the drawing is useful. The IEC 60617 database defines standard graphical symbols; confirm which symbol set your consultant uses before comparing drawings from different offices.
What to put on the SLD before you ask for a quotation
A panel supplier can only price what is defined. A drawing that is incomplete leads to assumptions, and assumptions lead to variations. Before you send an SLD for a quotation, check that it gives:
- the system voltage, number of phases, frequency and earthing system;
- the incomer rating and the short-circuit level it must withstand (from the designer or the utility);
- the type and rating of each breaker, and for adjustable devices the settings range required;
- the cable size and length of each feeder, so that voltage drop and protection can be checked;
- the load of each outgoing circuit, with spare ways if you want room for future loads;
- metering, surge protection and any communication or monitoring requirements;
- enclosure type, indoor or outdoor use, and the ambient temperature.
If you do not have a complete SLD, a technical design service can prepare it from the load list and the architectural drawings. See Technical Design and the Electrical Panel Assemblies service.
Common mistakes in single line diagrams
- Showing a breaker without its rating or breaking capacity. The drawing then cannot be priced or checked.
- Mixing up the MDB and SMDB levels, so that a sub-board is shown as fed directly from the transformer.
- Missing cable lengths, which hides voltage-drop problems.
- No spare ways, which makes any future load an extension project.
- Not matching the SLD to the panel schedule or the bill of quantities. Each device on the drawing should appear once in the schedule.
A quick checklist
- One source at the top, one clear path downward.
- Every device labelled with rating and type.
- Every cable labelled with size and length.
- Every load labelled with its power.
- Notes give voltage, earthing, enclosure and standards.
Requirements for submittals and approvals differ by project and authority, so confirm the requirement for your project with your consultant or the authority.
Need help with a panel drawing?
If you have an SLD, a load list or only a site description, Arab Arc Trading in Jeddah can review what you have and tell you what is missing before quotation. Send it through the contact page with the project location and the delivery date you need.
FAQ
What is the difference between a single line diagram and a wiring diagram?
An SLD shows the power path and the main devices on one line per circuit. A wiring diagram shows every conductor and terminal and is used to build and test the panel.
Who prepares the single line diagram?
Normally the project designer or consultant. A panel supplier can prepare a diagram from the load list when none exists, but it should be approved by the project's responsible engineer.
Does an SLD show the breaker brand?
It can. If you want a specific brand, write it in the notes or the device schedule; otherwise the supplier will quote equivalent devices.